Sieve Analysis of up to 3 kg Sample Weight
W.S. TYLER® Ro-Tap® RX-29 with CE labelling
The W.S. TYLER® Ro-Tap® RX-29 CE for test sieves up to 203 mm diameter reproduces the circular and tapping motion of hand sieving but with an even mechanical action. It differs from the W.S. TYLER® Ro-Tap® RX-29 in the safety cupboard which is necessary for CE conformity.
Most suitable machine for abrasive materials
- The safety cupboard and an an separate control gear meets the demands of job safety that are necessary for CE-labelling in Europe.
- Enables sieving of agglomerating bulk materials.
Prescribed in the FEPA-standard for abrasive industry.
Further advantages at a glance
- The 2D sieving action saves time and manual re-sieving.
- Easy handling – only sieving time has to be set.
Technical data
Sieve diameters | 200 mm, 203 mm (8") |
---|---|
Sample weight | approx. 3 kg |
Operating voltage | 230 Volt or 115 Volt, 50-60 Hertz |
Timer | 0-99 minutes |
Taps per minute | 150 |
Oscillations per minute | 278 |
Drive | electric motor with worm gear |
Sound emission | 70 dBA |
Weight | ca. 124 kg (without test sieves) |
Dimensions | 890 x 610 x 740 mm (B x T x H) |
W.S. TYLER® Ro-Tap® RX-29 CE - application examples
Diamonds
Abrasives
Metal powder and metal swarf
Powder
Tobacco
- Cacao
- Mining Industry
Suitable test sieves for your application
It depends on your application which test sieves should be used for sieve analysis with the W.S. TYLER® Ro-Tap® RX-29 CE. It is suitable for up to 6 test sieves with full height or 13 half-height sieves and one sieve pan with a diameter of up to 203 mm (8”) or 200 mm.
The W.S. TYLER® Ro-Tap® RX-29 CE is integrated in a safety cupboard and can only be started by means of an external control gear when the cupboard is closed. This provides job safety as injuries caused by the circular and tapping motion of the test sieve shaker are prevented.
E-Shop Particle Analysis
With this E-Shop button the required test sieve shaker can be specified directly.
Click here to find all spare parts for W.S. TYLER® Ro-Tap®.
Item | Description | Part No. |
---|---|---|
1 | Base | 107770 |
2 | Hammer | R-20029 |
3 | Hammer Block | R-20023 |
4 | Sheet Guard | R-30019 |
5 | Rotating Guard | R-30010 |
6 | Lift Rod | R-10036 |
7 | Upper Main Shaft Washer | R-10038 |
8 | Main Shaft | R-20027 |
9 | Upper Carrying Plate (plastic) RX-29 | R-30008 |
9A | Upper Carrying Plate (aluminium) RX-29 | R-30008-1 |
9B* | Upper Carrying Plate (steel) RX-30 | R-30027 |
10 | Lower Carrying Plate | R-30009 |
12 | Cam Gear | R-20039 |
13 | Timing Belt Pulley | R-30015 |
14 | Eccentric Disc | R-10034 |
15 | Block | R-10032 |
16 | Sieve Cover Ro-Tap® RX-29 | R-30007 |
16A | Sieve Cover Ro-Tap® RX-30 | R-30011 |
17 | Sieve Support Plate RX-29 | R-30006 |
17A | Sieve support plate RX-30 | R-30013 |
18 | Sieve support clamp bar RX-29 | R-30023 |
18A | Sieve support clamp bar RX-30 | R-30022 |
19 | Backup Plate | R-20019 |
20 | Bearing Plate | R-20020 |
21 | Shield | R-20033 |
22 | Tube Spacer | R-10028 |
23 | Cam Shoulder Screw | R-10029 |
23A | 1/2" I.D. Shim | 106582 |
24 | Main Shaft Key to Eccentric | R-10042 |
25 | Main Shaft Key - Lower | R-10039 |
26 | Hammer Pin | R-10035 |
27 | Cork Plug | R-10066A |
29 | Tie Rod | R-10033 |
30 | Motor Adaptor | R-30018 |
31 | Grommet | ZA11167 |
* position not marked
Item | Description | Part No. |
---|---|---|
32 | Lift Rod Coupling (2 1/2" lg.) | R-10030 |
33 | Pedestal Cover | R-40011 |
34 | Flange Bearing | R-10061 |
35 | Bearing | R-10062 |
36 | Flange Bearing | R-10063 |
37 | Thrust Washer | ZF-10168 |
38 | Steel Bushing | R-10065 |
39 | 3/8-16 NC x 2,25" Carriage Bolt | ZF-10174 |
40 | Sprocket-14 teeth (1800 RPM) w/Set Screw | R-10070 |
40 | Sprocket-17 teeth (1500 RPM) w/Set Screw | R-10048 |
41 | Electronic timer (230 V, 50 Hz) | R-40029 |
41 | Electronic timer (110 V, 60 Hz) | R-40037 |
41A | Timer Mounting Clip | R-40040 |
42 | Motor Standard 115/230 V, 60/50 Hz 1 Phase | P-1500-23 |
42A | 3/8-16 x 1" long Hex Head Screw | ZF-10183 |
42B | 3/8 I.D. Flat Washer | ZF-10168 |
43 | Timing Belt | R-10058 |
44 | Shim | R-10055 |
45 | 1/2-13x2,50" long Hex Hd. Bolt | ZZ-10068 |
45A | 1/2 I.D. Lock Washer | ZZ-10323 |
47 | Clamp Screw | R-10079 |
48 | 3/8" Lock Nut | ZF-10221 |
49 | 1/2" Lock Nut | ZF-10222 |
50 | 10-32x0,50" long Flat Head Socket Cap Screw | ZF-10231 |
51 | 3/8-16x.75" long Flat Head Socket Cap Screw | ZF-10241 |
51A | 3/8-16x.1" long Hex Head Screw (replaces ZF-10183) | ZF-10240 |
52 | 3/8-16x.62" long Hex Hd. Screw | 114162 |
53 | 5/16-24x1.25" long Socket Head Cap Screw | ZF-10251 |
54 | handles for sieve support plate (=1 pair) | R-20082 |
55 | #10-24x.25" Socket hd. Set Screw | ZA-10148 |
56 | 3/8 I.D.x1.50" O.D. Fender Washer | ZF-10271 |
60* | Timer Cord w/Plug | R-10018 |
61* | Straight Connector (APC-050) | R-10112 |
62* | Flexible Conduit | 107764 |