Certification and Calibration of Test Sieves, Test Sieve Shakers and Dynamic Image Analysis

On-site quality assurance

We use our modern calibrated screen measuring systems for certifying new analysis sieves and re-certifying used ones. One of these is located in our plant laboratory. But with our mobile unit, we can also measure on-site, on your premises. The certified HAVER BSA measuring procedure determines whether the analysis sieves comply with the applicable standards.
With the mobile HAVER measurement system, Haver & Boecker can

  • certify or
  • calibrate

on-site.

 

With both methods, the woven wire meshes are measured in both the warp and weft direction. They differ from each other through the number of apertures to be measured, which results in statistical confidence levels.

During calibration, up to three times more apertures are measured than during certification. Each analysis sieve is always specifically tested. The determined mesh sizes are given separately for both the warp and weft direction.

The measurement results are stored and available for later evaluation.

  • Certification as to ISO 3310, ASTM E11, AFNOR, BS 410
  • Measurement protocol 3.1 as to EN 10 204 with tabular display of mesh sizes
  • On-site service  - directly at the customer, thus analysis sieves can go back into operation quickly

 

Test of Test Sieve Shakers


We test your test sieve analysis machines for function, condition and safety in your plant. The machines are subjected to comprehensive system diagnostics and function tests, during which, among other things, the amplitude characteristic is determined and, if necessary, readjusted. After successful testing, we issue a final acceptance test certificate 3.1 as to DIN EN 10204. Should we detect any faults, then we will submit a cost estimate for repair and maintenance. We recommend an inspection every two to three years if the sieve machine is used frequently,

CERTIFICATION

  • Measurement of test sieves using mobile BSA system in the range 20 μm – 2.0 mm
  • Mesh and opening  sizes > 2.0 mm using calipers
  • Standards: ISO 3310-1 and ISO 3310-2, ASTM E11
  • Electroformed Sheets: ISO 3310-3  > 20µm
  • Time expenditure per sieve / 5 min – 30 min

 

CALIBRATION

  • Measurement of test sieves using mobile BSA system in the range 20 μm – 2.0 mm
  • Mesh and opening sizes > 2.0 mm using calipers
  • Standards: ISO 3310-1 and ISO 3310-2, ASTM E11
  • Time expenditure per sieve / 10 min - 1 hour and more

 

CERTIFICATION / CALIBRATION AS TO DIN EN ISO / IEC 17025

Only in an accredited plant laboratory in Oelde and exclusively for analysis sieves with      woven wire mesh possible. Larger quantities must first be coordinated with the plant laboratory.

 

GRID SIEVES

  • Standard DIN EN 10204: by comparison checks using measurement gauges

SMALL MACHINE SERVICE EML LABORATORY SIEVE MACHINES

  • Function test (Visual check of sieve machine condition, Amplitude check with calibration, Function check of interval mode, Function check of timer switch, Trial operation)
  • Acceptance test certificate 3.1

 

 

LARGE MACHINE SERVICE EML LABORATORY SIEVE MACHINES

  • Expanded function test* (Cleaning of the magnets, Checking the air gap and adjust if needed, Checking the seal, Checking the fuse and replace if needed, Assessment of flat spring and replace if needed, Cleaning TwinNut or Classic tension system and lubricate relevant components)
  • Amplitude measurement and calibration
  • Service report
  • Acceptance test certificate 3.1

Warranty extended 1 year

*This includes the above works, but also the following checks.

 

 

SMALL MACHINE SERVICE W.S. TYLER RO-TAP® RX-29

  • Functional check (Visual check of screening  machine condition, Amplitude check with calibration, Function check of interval mode, Function check of timer switch, Trial run)
  • Measurement of rotational speed and tapping impulses
  • Checking and adjusting the correct hammer height
  • Inspection certificate 3.1

 

 

LARGE MACHINE SERVICE W.S. TYLER RO-TAP® RX-29

  • Extended function test* (Cleaning the magnet, Checking the air gap and readjust if necessary, Checking the seal, Checking the fuse, replace if necessary, Inspection of the leaf springs and possible replacement,
    Cleaning the TwinNut or Classic tensioning system and Lubrication of relevant components, Inspection of the guides and bearings for wear, Exchange of defective components after consultation with
    customer (major repair work only at the Oelde-Germany plant possible), Measurement of the rotational speed and knocking impulses
  • Checking and adjusting the correct hammer height
  • Inspection certificate 3.1

Warranty extended 1 year

*This includes the above works, but also the following checks.

 

 

START-UP AND TRAINING AS TO GMP

  • Sieve machine installation
  • Hook-up of the laboratory sieve machines
  • Inspection as to IQ/OQ documentation
  • Amplitude calibration (EML sieve machines)
  • Hammer height adjustment (RO-TAP® only)
  • Start-up
  • Training of technical staff

Travel expenses

  • Flat rate per km for arrival and departure / costs for car rental / costs for air travel / costs for rail travel
  • Hourly rate for arrival and departure
  • Accommodation costs and allowances (abroad according to German tax code)
  • Other additional costs (visa, tolls)

Processing fee*

  • One-time expense allowance

* Processing fee is waived if a service contract was previously concluded.

MAINTENANCE AND CALIBRATION HAVER CPA LABORATORY INSTRUMENT

  • Cleaning functionally relevant components
  • Function test
  • Software update installation (if technically possible and necessary)
  • Calibration using test equipment
  • Documentation of results
  • Creation of data backup
  • Back-up data on HB-Server (if desired)
  • Attaching test sticker to the device
  • Inspection certificate 3.1

Travel expenses

  • Flat rate per km for arrival and departure / costs for car rental / costs for air travel / costs for rail travel
  • Hourly rate for arrival and departure
  • Accommodation costs and allowances (abroad according to German tax code)
  • Other additional costs (visa, tolls)

Processing fee*

  • One-time expense allowance

* The processing fee is waived if a service contract was previously concluded.

The complete service offer for download...


Particle Analysis | Phone: +49 (0) 25 22 - 30 131 | Fax: +49 (0) 25 22 - 30 152 | pa@haverboecker.com
Dynamic Image Analysis | Phone: +49 (0) 25 22 - 30 150 | Fax: +49 (0) 25 22 - 30 152 | cpa@haverboecker.com
Top